ADD (M32, I8)

With unroll_count=500 and no inner loop

Code:

   0:	41 83 06 02          	add    DWORD PTR [r14],0x2

Show nanoBench command
Results:
- Instructions retired: 1.0
- Core cycles: 5.0
- Reference cycles: 3.28
- UOPS_RETIRED.ANY: 1.0
- UOPS_MS: 0.0

With loop_count=1000 and unroll_count=10

Code:

   0:	41 83 06 02          	add    DWORD PTR [r14],0x2

Show nanoBench command
Results:
- Instructions retired: 1.2
- Core cycles: 5.0
- Reference cycles: 3.27
- UOPS_RETIRED.ANY: 1.2
- UOPS_MS: 0.0

With loop_count=100 and unroll_count=100

Code:

   0:	41 83 06 02          	add    DWORD PTR [r14],0x2

Show nanoBench command
Results:
- Instructions retired: 1.02
- Core cycles: 5.0
- Reference cycles: 3.26
- UOPS_RETIRED.ANY: 1.02
- UOPS_MS: 0.0

With 4 independent instructions

With unroll_count=200 and no inner loop

Code:

   0:	41 83 06 02          	add    DWORD PTR [r14],0x2
   4:	41 83 46 04 02       	add    DWORD PTR [r14+0x4],0x2
   9:	41 83 46 08 02       	add    DWORD PTR [r14+0x8],0x2
   e:	41 83 46 0c 02       	add    DWORD PTR [r14+0xc],0x2

Show nanoBench command
Results:
- Instructions retired: 4.0
- Core cycles: 4.0
- Reference cycles: 2.41
- UOPS_RETIRED.ANY: 4.0
- UOPS_MS: 0.0

With loop_count=1000 and unroll_count=2

Code:

   0:	41 83 06 02          	add    DWORD PTR [r14],0x2
   4:	41 83 46 04 02       	add    DWORD PTR [r14+0x4],0x2
   9:	41 83 46 08 02       	add    DWORD PTR [r14+0x8],0x2
   e:	41 83 46 0c 02       	add    DWORD PTR [r14+0xc],0x2

Show nanoBench command
Results:
- Instructions retired: 5.0
- Core cycles: 6.01
- Reference cycles: 3.92
- UOPS_RETIRED.ANY: 5.0
- UOPS_MS: 0.0

With loop_count=100 and unroll_count=20

Code:

   0:	41 83 06 02          	add    DWORD PTR [r14],0x2
   4:	41 83 46 04 02       	add    DWORD PTR [r14+0x4],0x2
   9:	41 83 46 08 02       	add    DWORD PTR [r14+0x8],0x2
   e:	41 83 46 0c 02       	add    DWORD PTR [r14+0xc],0x2

Show nanoBench command
Results:
- Instructions retired: 4.1
- Core cycles: 4.92
- Reference cycles: 3.2
- UOPS_RETIRED.ANY: 4.1
- UOPS_MS: 0.0

With 8 independent instructions

With unroll_count=100 and no inner loop

Code:

   0:	41 83 06 02          	add    DWORD PTR [r14],0x2
   4:	41 83 46 04 02       	add    DWORD PTR [r14+0x4],0x2
   9:	41 83 46 08 02       	add    DWORD PTR [r14+0x8],0x2
   e:	41 83 46 0c 02       	add    DWORD PTR [r14+0xc],0x2
  13:	41 83 46 10 02       	add    DWORD PTR [r14+0x10],0x2
  18:	41 83 46 14 02       	add    DWORD PTR [r14+0x14],0x2
  1d:	41 83 46 18 02       	add    DWORD PTR [r14+0x18],0x2
  22:	41 83 46 1c 02       	add    DWORD PTR [r14+0x1c],0x2

Show nanoBench command
Results:
- Instructions retired: 8.0
- Core cycles: 7.99
- Reference cycles: 4.68
- UOPS_RETIRED.ANY: 8.0
- UOPS_MS: 0.0

With loop_count=1000 and unroll_count=1

Code:

   0:	41 83 06 02          	add    DWORD PTR [r14],0x2
   4:	41 83 46 04 02       	add    DWORD PTR [r14+0x4],0x2
   9:	41 83 46 08 02       	add    DWORD PTR [r14+0x8],0x2
   e:	41 83 46 0c 02       	add    DWORD PTR [r14+0xc],0x2
  13:	41 83 46 10 02       	add    DWORD PTR [r14+0x10],0x2
  18:	41 83 46 14 02       	add    DWORD PTR [r14+0x14],0x2
  1d:	41 83 46 18 02       	add    DWORD PTR [r14+0x18],0x2
  22:	41 83 46 1c 02       	add    DWORD PTR [r14+0x1c],0x2

Show nanoBench command
Results:
- Instructions retired: 10.0
- Core cycles: 8.02
- Reference cycles: 5.23
- UOPS_RETIRED.ANY: 10.0
- UOPS_MS: 0.0

With loop_count=100 and unroll_count=10

Code:

   0:	41 83 06 02          	add    DWORD PTR [r14],0x2
   4:	41 83 46 04 02       	add    DWORD PTR [r14+0x4],0x2
   9:	41 83 46 08 02       	add    DWORD PTR [r14+0x8],0x2
   e:	41 83 46 0c 02       	add    DWORD PTR [r14+0xc],0x2
  13:	41 83 46 10 02       	add    DWORD PTR [r14+0x10],0x2
  18:	41 83 46 14 02       	add    DWORD PTR [r14+0x14],0x2
  1d:	41 83 46 18 02       	add    DWORD PTR [r14+0x18],0x2
  22:	41 83 46 1c 02       	add    DWORD PTR [r14+0x1c],0x2

Show nanoBench command
Results:
- Instructions retired: 8.2
- Core cycles: 8.02
- Reference cycles: 5.23
- UOPS_RETIRED.ANY: 8.2
- UOPS_MS: 0.0

With 16 independent instructions

With unroll_count=100 and no inner loop

Code:

   0:	41 83 06 02          	add    DWORD PTR [r14],0x2
   4:	41 83 46 04 02       	add    DWORD PTR [r14+0x4],0x2
   9:	41 83 46 08 02       	add    DWORD PTR [r14+0x8],0x2
   e:	41 83 46 0c 02       	add    DWORD PTR [r14+0xc],0x2
  13:	41 83 46 10 02       	add    DWORD PTR [r14+0x10],0x2
  18:	41 83 46 14 02       	add    DWORD PTR [r14+0x14],0x2
  1d:	41 83 46 18 02       	add    DWORD PTR [r14+0x18],0x2
  22:	41 83 46 1c 02       	add    DWORD PTR [r14+0x1c],0x2
  27:	41 83 46 20 02       	add    DWORD PTR [r14+0x20],0x2
  2c:	41 83 46 24 02       	add    DWORD PTR [r14+0x24],0x2
  31:	41 83 46 28 02       	add    DWORD PTR [r14+0x28],0x2
  36:	41 83 46 2c 02       	add    DWORD PTR [r14+0x2c],0x2
  3b:	41 83 46 30 02       	add    DWORD PTR [r14+0x30],0x2
  40:	41 83 46 34 02       	add    DWORD PTR [r14+0x34],0x2
  45:	41 83 46 38 02       	add    DWORD PTR [r14+0x38],0x2
  4a:	41 83 46 3c 02       	add    DWORD PTR [r14+0x3c],0x2

Show nanoBench command
Results:
- Instructions retired: 16.0
- Core cycles: 16.01
- Reference cycles: 10.92
- UOPS_RETIRED.ANY: 16.0
- UOPS_MS: 0.0

With loop_count=1000 and unroll_count=1

Code:

   0:	41 83 06 02          	add    DWORD PTR [r14],0x2
   4:	41 83 46 04 02       	add    DWORD PTR [r14+0x4],0x2
   9:	41 83 46 08 02       	add    DWORD PTR [r14+0x8],0x2
   e:	41 83 46 0c 02       	add    DWORD PTR [r14+0xc],0x2
  13:	41 83 46 10 02       	add    DWORD PTR [r14+0x10],0x2
  18:	41 83 46 14 02       	add    DWORD PTR [r14+0x14],0x2
  1d:	41 83 46 18 02       	add    DWORD PTR [r14+0x18],0x2
  22:	41 83 46 1c 02       	add    DWORD PTR [r14+0x1c],0x2
  27:	41 83 46 20 02       	add    DWORD PTR [r14+0x20],0x2
  2c:	41 83 46 24 02       	add    DWORD PTR [r14+0x24],0x2
  31:	41 83 46 28 02       	add    DWORD PTR [r14+0x28],0x2
  36:	41 83 46 2c 02       	add    DWORD PTR [r14+0x2c],0x2
  3b:	41 83 46 30 02       	add    DWORD PTR [r14+0x30],0x2
  40:	41 83 46 34 02       	add    DWORD PTR [r14+0x34],0x2
  45:	41 83 46 38 02       	add    DWORD PTR [r14+0x38],0x2
  4a:	41 83 46 3c 02       	add    DWORD PTR [r14+0x3c],0x2

Show nanoBench command
Results:
- Instructions retired: 18.0
- Core cycles: 16.02
- Reference cycles: 10.45
- UOPS_RETIRED.ANY: 18.0
- UOPS_MS: 0.0

With loop_count=100 and unroll_count=10

Code:

   0:	41 83 06 02          	add    DWORD PTR [r14],0x2
   4:	41 83 46 04 02       	add    DWORD PTR [r14+0x4],0x2
   9:	41 83 46 08 02       	add    DWORD PTR [r14+0x8],0x2
   e:	41 83 46 0c 02       	add    DWORD PTR [r14+0xc],0x2
  13:	41 83 46 10 02       	add    DWORD PTR [r14+0x10],0x2
  18:	41 83 46 14 02       	add    DWORD PTR [r14+0x14],0x2
  1d:	41 83 46 18 02       	add    DWORD PTR [r14+0x18],0x2
  22:	41 83 46 1c 02       	add    DWORD PTR [r14+0x1c],0x2
  27:	41 83 46 20 02       	add    DWORD PTR [r14+0x20],0x2
  2c:	41 83 46 24 02       	add    DWORD PTR [r14+0x24],0x2
  31:	41 83 46 28 02       	add    DWORD PTR [r14+0x28],0x2
  36:	41 83 46 2c 02       	add    DWORD PTR [r14+0x2c],0x2
  3b:	41 83 46 30 02       	add    DWORD PTR [r14+0x30],0x2
  40:	41 83 46 34 02       	add    DWORD PTR [r14+0x34],0x2
  45:	41 83 46 38 02       	add    DWORD PTR [r14+0x38],0x2
  4a:	41 83 46 3c 02       	add    DWORD PTR [r14+0x3c],0x2

Show nanoBench command
Results:
- Instructions retired: 16.2
- Core cycles: 16.02
- Reference cycles: 10.45
- UOPS_RETIRED.ANY: 16.2
- UOPS_MS: 0.0

With an indexed addressing mode

With 1 independent instruction

With unroll_count=500 and no inner loop

Code:

   0:	43 83 04 2e 02       	add    DWORD PTR [r14+r13*1],0x2

Init:
```
XOR R13, R13
```
Show nanoBench command
Results:
- Instructions retired: 1.0
- Core cycles: 5.0
- Reference cycles: 3.25
- UOPS_RETIRED.ANY: 1.0
- UOPS_MS: 0.0

With loop_count=1000 and unroll_count=10

Code:

   0:	43 83 04 2e 02       	add    DWORD PTR [r14+r13*1],0x2

Init:
```
XOR R13, R13
```
Show nanoBench command
Results:
- Instructions retired: 1.2
- Core cycles: 5.0
- Reference cycles: 3.27
- UOPS_RETIRED.ANY: 1.2
- UOPS_MS: 0.0

With loop_count=100 and unroll_count=100

Code:

   0:	43 83 04 2e 02       	add    DWORD PTR [r14+r13*1],0x2

Init:
```
XOR R13, R13
```
Show nanoBench command
Results:
- Instructions retired: 1.02
- Core cycles: 5.0
- Reference cycles: 3.26
- UOPS_RETIRED.ANY: 1.02
- UOPS_MS: 0.0

With 4 independent instructions

With unroll_count=200 and no inner loop

Code:

   0:	43 83 04 2e 02       	add    DWORD PTR [r14+r13*1],0x2
   5:	43 83 44 2e 04 02    	add    DWORD PTR [r14+r13*1+0x4],0x2
   b:	43 83 44 2e 08 02    	add    DWORD PTR [r14+r13*1+0x8],0x2
  11:	43 83 44 2e 0c 02    	add    DWORD PTR [r14+r13*1+0xc],0x2

Init:
```
XOR R13, R13
```
Show nanoBench command
Results:
- Instructions retired: 4.0
- Core cycles: 4.0
- Reference cycles: 2.6
- UOPS_RETIRED.ANY: 4.0
- UOPS_MS: 0.0

With loop_count=1000 and unroll_count=2

Code:

   0:	43 83 04 2e 02       	add    DWORD PTR [r14+r13*1],0x2
   5:	43 83 44 2e 04 02    	add    DWORD PTR [r14+r13*1+0x4],0x2
   b:	43 83 44 2e 08 02    	add    DWORD PTR [r14+r13*1+0x8],0x2
  11:	43 83 44 2e 0c 02    	add    DWORD PTR [r14+r13*1+0xc],0x2

Init:
```
XOR R13, R13
```
Show nanoBench command
Results:
- Instructions retired: 5.0
- Core cycles: 6.01
- Reference cycles: 3.92
- UOPS_RETIRED.ANY: 5.0
- UOPS_MS: 0.0

With loop_count=100 and unroll_count=20

Code:

   0:	43 83 04 2e 02       	add    DWORD PTR [r14+r13*1],0x2
   5:	43 83 44 2e 04 02    	add    DWORD PTR [r14+r13*1+0x4],0x2
   b:	43 83 44 2e 08 02    	add    DWORD PTR [r14+r13*1+0x8],0x2
  11:	43 83 44 2e 0c 02    	add    DWORD PTR [r14+r13*1+0xc],0x2

Init:
```
XOR R13, R13
```
Show nanoBench command
Results:
- Instructions retired: 4.1
- Core cycles: 4.99
- Reference cycles: 3.26
- UOPS_RETIRED.ANY: 4.1
- UOPS_MS: 0.0

With 8 independent instructions

With unroll_count=100 and no inner loop

Code:

   0:	43 83 04 2e 02       	add    DWORD PTR [r14+r13*1],0x2
   5:	43 83 44 2e 04 02    	add    DWORD PTR [r14+r13*1+0x4],0x2
   b:	43 83 44 2e 08 02    	add    DWORD PTR [r14+r13*1+0x8],0x2
  11:	43 83 44 2e 0c 02    	add    DWORD PTR [r14+r13*1+0xc],0x2
  17:	43 83 44 2e 10 02    	add    DWORD PTR [r14+r13*1+0x10],0x2
  1d:	43 83 44 2e 14 02    	add    DWORD PTR [r14+r13*1+0x14],0x2
  23:	43 83 44 2e 18 02    	add    DWORD PTR [r14+r13*1+0x18],0x2
  29:	43 83 44 2e 1c 02    	add    DWORD PTR [r14+r13*1+0x1c],0x2

Init:
```
XOR R13, R13
```
Show nanoBench command
Results:
- Instructions retired: 8.0
- Core cycles: 8.0
- Reference cycles: 4.94
- UOPS_RETIRED.ANY: 8.0
- UOPS_MS: 0.0

With loop_count=1000 and unroll_count=1

Code:

   0:	43 83 04 2e 02       	add    DWORD PTR [r14+r13*1],0x2
   5:	43 83 44 2e 04 02    	add    DWORD PTR [r14+r13*1+0x4],0x2
   b:	43 83 44 2e 08 02    	add    DWORD PTR [r14+r13*1+0x8],0x2
  11:	43 83 44 2e 0c 02    	add    DWORD PTR [r14+r13*1+0xc],0x2
  17:	43 83 44 2e 10 02    	add    DWORD PTR [r14+r13*1+0x10],0x2
  1d:	43 83 44 2e 14 02    	add    DWORD PTR [r14+r13*1+0x14],0x2
  23:	43 83 44 2e 18 02    	add    DWORD PTR [r14+r13*1+0x18],0x2
  29:	43 83 44 2e 1c 02    	add    DWORD PTR [r14+r13*1+0x1c],0x2

Init:
```
XOR R13, R13
```
Show nanoBench command
Results:
- Instructions retired: 10.0
- Core cycles: 8.02
- Reference cycles: 5.23
- UOPS_RETIRED.ANY: 10.0
- UOPS_MS: 0.0

With loop_count=100 and unroll_count=10

Code:

   0:	43 83 04 2e 02       	add    DWORD PTR [r14+r13*1],0x2
   5:	43 83 44 2e 04 02    	add    DWORD PTR [r14+r13*1+0x4],0x2
   b:	43 83 44 2e 08 02    	add    DWORD PTR [r14+r13*1+0x8],0x2
  11:	43 83 44 2e 0c 02    	add    DWORD PTR [r14+r13*1+0xc],0x2
  17:	43 83 44 2e 10 02    	add    DWORD PTR [r14+r13*1+0x10],0x2
  1d:	43 83 44 2e 14 02    	add    DWORD PTR [r14+r13*1+0x14],0x2
  23:	43 83 44 2e 18 02    	add    DWORD PTR [r14+r13*1+0x18],0x2
  29:	43 83 44 2e 1c 02    	add    DWORD PTR [r14+r13*1+0x1c],0x2

Init:
```
XOR R13, R13
```
Show nanoBench command
Results:
- Instructions retired: 8.2
- Core cycles: 8.02
- Reference cycles: 5.23
- UOPS_RETIRED.ANY: 8.2
- UOPS_MS: 0.0

With 16 independent instructions

With unroll_count=100 and no inner loop

Code:

   0:	43 83 04 2e 02       	add    DWORD PTR [r14+r13*1],0x2
   5:	43 83 44 2e 04 02    	add    DWORD PTR [r14+r13*1+0x4],0x2
   b:	43 83 44 2e 08 02    	add    DWORD PTR [r14+r13*1+0x8],0x2
  11:	43 83 44 2e 0c 02    	add    DWORD PTR [r14+r13*1+0xc],0x2
  17:	43 83 44 2e 10 02    	add    DWORD PTR [r14+r13*1+0x10],0x2
  1d:	43 83 44 2e 14 02    	add    DWORD PTR [r14+r13*1+0x14],0x2
  23:	43 83 44 2e 18 02    	add    DWORD PTR [r14+r13*1+0x18],0x2
  29:	43 83 44 2e 1c 02    	add    DWORD PTR [r14+r13*1+0x1c],0x2
  2f:	43 83 44 2e 20 02    	add    DWORD PTR [r14+r13*1+0x20],0x2
  35:	43 83 44 2e 24 02    	add    DWORD PTR [r14+r13*1+0x24],0x2
  3b:	43 83 44 2e 28 02    	add    DWORD PTR [r14+r13*1+0x28],0x2
  41:	43 83 44 2e 2c 02    	add    DWORD PTR [r14+r13*1+0x2c],0x2
  47:	43 83 44 2e 30 02    	add    DWORD PTR [r14+r13*1+0x30],0x2
  4d:	43 83 44 2e 34 02    	add    DWORD PTR [r14+r13*1+0x34],0x2
  53:	43 83 44 2e 38 02    	add    DWORD PTR [r14+r13*1+0x38],0x2
  59:	43 83 44 2e 3c 02    	add    DWORD PTR [r14+r13*1+0x3c],0x2

Init:
```
XOR R13, R13
```
Show nanoBench command
Results:
- Instructions retired: 16.0
- Core cycles: 16.0
- Reference cycles: 9.88
- UOPS_RETIRED.ANY: 16.0
- UOPS_MS: 0.0

With loop_count=1000 and unroll_count=1

Code:

   0:	43 83 04 2e 02       	add    DWORD PTR [r14+r13*1],0x2
   5:	43 83 44 2e 04 02    	add    DWORD PTR [r14+r13*1+0x4],0x2
   b:	43 83 44 2e 08 02    	add    DWORD PTR [r14+r13*1+0x8],0x2
  11:	43 83 44 2e 0c 02    	add    DWORD PTR [r14+r13*1+0xc],0x2
  17:	43 83 44 2e 10 02    	add    DWORD PTR [r14+r13*1+0x10],0x2
  1d:	43 83 44 2e 14 02    	add    DWORD PTR [r14+r13*1+0x14],0x2
  23:	43 83 44 2e 18 02    	add    DWORD PTR [r14+r13*1+0x18],0x2
  29:	43 83 44 2e 1c 02    	add    DWORD PTR [r14+r13*1+0x1c],0x2
  2f:	43 83 44 2e 20 02    	add    DWORD PTR [r14+r13*1+0x20],0x2
  35:	43 83 44 2e 24 02    	add    DWORD PTR [r14+r13*1+0x24],0x2
  3b:	43 83 44 2e 28 02    	add    DWORD PTR [r14+r13*1+0x28],0x2
  41:	43 83 44 2e 2c 02    	add    DWORD PTR [r14+r13*1+0x2c],0x2
  47:	43 83 44 2e 30 02    	add    DWORD PTR [r14+r13*1+0x30],0x2
  4d:	43 83 44 2e 34 02    	add    DWORD PTR [r14+r13*1+0x34],0x2
  53:	43 83 44 2e 38 02    	add    DWORD PTR [r14+r13*1+0x38],0x2
  59:	43 83 44 2e 3c 02    	add    DWORD PTR [r14+r13*1+0x3c],0x2

Init:
```
XOR R13, R13
```
Show nanoBench command
Results:
- Instructions retired: 18.0
- Core cycles: 16.02
- Reference cycles: 10.45
- UOPS_RETIRED.ANY: 18.0
- UOPS_MS: 0.0

With loop_count=100 and unroll_count=10

Code:

   0:	43 83 04 2e 02       	add    DWORD PTR [r14+r13*1],0x2
   5:	43 83 44 2e 04 02    	add    DWORD PTR [r14+r13*1+0x4],0x2
   b:	43 83 44 2e 08 02    	add    DWORD PTR [r14+r13*1+0x8],0x2
  11:	43 83 44 2e 0c 02    	add    DWORD PTR [r14+r13*1+0xc],0x2
  17:	43 83 44 2e 10 02    	add    DWORD PTR [r14+r13*1+0x10],0x2
  1d:	43 83 44 2e 14 02    	add    DWORD PTR [r14+r13*1+0x14],0x2
  23:	43 83 44 2e 18 02    	add    DWORD PTR [r14+r13*1+0x18],0x2
  29:	43 83 44 2e 1c 02    	add    DWORD PTR [r14+r13*1+0x1c],0x2
  2f:	43 83 44 2e 20 02    	add    DWORD PTR [r14+r13*1+0x20],0x2
  35:	43 83 44 2e 24 02    	add    DWORD PTR [r14+r13*1+0x24],0x2
  3b:	43 83 44 2e 28 02    	add    DWORD PTR [r14+r13*1+0x28],0x2
  41:	43 83 44 2e 2c 02    	add    DWORD PTR [r14+r13*1+0x2c],0x2
  47:	43 83 44 2e 30 02    	add    DWORD PTR [r14+r13*1+0x30],0x2
  4d:	43 83 44 2e 34 02    	add    DWORD PTR [r14+r13*1+0x34],0x2
  53:	43 83 44 2e 38 02    	add    DWORD PTR [r14+r13*1+0x38],0x2
  59:	43 83 44 2e 3c 02    	add    DWORD PTR [r14+r13*1+0x3c],0x2

Init:
```
XOR R13, R13
```
Show nanoBench command
Results:
- Instructions retired: 16.2
- Core cycles: 16.02
- Reference cycles: 10.45
- UOPS_RETIRED.ANY: 16.2
- UOPS_MS: 0.0

ADD (M32, I8) - Throughput and Uops

With a non-indexed addressing mode

With 1 independent instruction

With unroll_count=500 and no inner loop

With loop_count=1000 and unroll_count=10

With loop_count=100 and unroll_count=100

With 4 independent instructions

With unroll_count=200 and no inner loop

With loop_count=1000 and unroll_count=2

With loop_count=100 and unroll_count=20

With 8 independent instructions

With unroll_count=100 and no inner loop

With loop_count=1000 and unroll_count=1

With loop_count=100 and unroll_count=10

With 16 independent instructions

With unroll_count=100 and no inner loop

With loop_count=1000 and unroll_count=1

With loop_count=100 and unroll_count=10

With an indexed addressing mode

With 1 independent instruction

With unroll_count=500 and no inner loop

With loop_count=1000 and unroll_count=10

With loop_count=100 and unroll_count=100

With 4 independent instructions

With unroll_count=200 and no inner loop

With loop_count=1000 and unroll_count=2

With loop_count=100 and unroll_count=20

With 8 independent instructions

With unroll_count=100 and no inner loop

With loop_count=1000 and unroll_count=1

With loop_count=100 and unroll_count=10

With 16 independent instructions

With unroll_count=100 and no inner loop

With loop_count=1000 and unroll_count=1

With loop_count=100 and unroll_count=10